Compression Behavior of FFF Printed Parts Obtained by Varying Layer Height and Infill Percentage
Received: 15 November 2022 | Revised: 28 November 2022 | Accepted: 2 December 2022 | Online: 12 December 2022
Corresponding author: A. I. Portoaca
Abstract
In this research, two polymeric materials, PLA-(polylactic acid) and ABS (acrylonitrile butadiene styrene) were used to 3D print compression samples at 3 layer heights (0.10, 0.15, and 0.20mm) with 3 infill percentages (50%, 75%, 100%). In order to determine the material's behavior under applied crushing loads, 135 samples were fabricated and tested. The built compression PLA specimens were subjected to common annealing treatment just above glass transition temperature and it was proved that the set of 45 samples exhibited higher resistance to the compressive load applied to the material before fracturing by an average of 9.20%.
Keywords:
printing, annealing, compressive test, post-porcessing treatmentsDownloads
References
B. A. Bimber, R. F. Hamilton, J. Keist, and T. A. Palmer, "Anisotropic microstructure and superelasticity of additive manufactured NiTi alloy bulk builds using laser directed energy deposition," Materials Science and Engineering: A, vol. 674, pp. 125–134, Sep. 2016. DOI: https://doi.org/10.1016/j.msea.2016.07.059
N. Narlıoğlu, "Comparison of mechanical properties of 3D-printed and compression-molded wood-polylactic acid (PLA) composites :: BioResources," BioResources, vol. 17, no. 2, pp. 3291–3302, 2022. DOI: https://doi.org/10.15376/biores.17.2.3291-3302
A. Hrituc et al., "Mechanical Behaviour of 3D Printed PLA Hollow Spherical Parts Under Axial Compression," Materiale Plastice, vol. 57, no. 1, pp. 13–20, Apr. 2020. DOI: https://doi.org/10.37358/MP.20.1.5307
S. Brischetto and R. Torre, "Tensile and Compressive Behavior in the Experimental Tests for PLA Specimens Produced via Fused Deposition Modelling Technique," Journal of Composites Science, vol. 4, no. 3, Sep. 2020, Art. no. 140. DOI: https://doi.org/10.3390/jcs4030140
R. F. Hamilton, B. A. Bimber, and T. A. Palmer, "Correlating microstructure and superelasticity of directed energy deposition additive manufactured Ni-rich NiTi alloys," Journal of Alloys and Compounds, vol. 739, pp. 712–722, Mar. 2018. DOI: https://doi.org/10.1016/j.jallcom.2017.12.270
M. Ali, R. K. Sari, U. Sajjad, M. Sultan, and H. M. Ali, "Effect of annealing on microstructures and mechanical properties of PA-12 lattice structures proceeded by multi jet fusion technology," Additive Manufacturing, vol. 47, Nov. 2021, Art. no. 102285. DOI: https://doi.org/10.1016/j.addma.2021.102285
M. Saleh, S. Anwar, A. M. Al-Ahmari, and A. Alfaify, "Compression Performance and Failure Analysis of 3D-Printed Carbon Fiber/PLA Composite TPMS Lattice Structures," Polymers, vol. 14, no. 21, Jan. 2022, Art. no. 4595. DOI: https://doi.org/10.3390/polym14214595
M. Minescu and D. G. Zisopol, Sudarea țevilor şi fitingurilor din polietilenă de înaltă densitate (HDPE Pipe & Fittings Welding). Ploiesti, Romania: Editura Universității Petrol-Gaze din Ploiești, 2021.
D. G. Zisopol and A. Dumitrescu, Ecotehnologie. Studii ce caz. Ploiesti, Romania: Editura Universității Petrol-Gaze din Ploiești, 2020.
D. G. Zisopol, A. Dumitrescu, and C. N. Trifan, Ecotehnologie: Noţiuni teoretice, aplicaţii şi studii de caz. Ploiesti, Romania, 2010.
D. G. Zisopol and M. J. Săvulescu, Bazele tehnologiei. Ploiesti, Romania, 2003.
D. G. Zisopol, Tehnologii industriale și de construcții, Aplicații practice și studii de caz. Ploiesti, Romania, 2003.
M. J. Săvulescu and D. G. Zisopol, Tehnologii industriale şi de construcţii. Ploiesti, Romania, 2002.
M. R. Khosravani, F. Berto, M. R. Ayatollahi, and T. Reinicke, "Characterization of 3D-printed PLA parts with different raster orientations and printing speeds," Scientific Reports, vol. 12, no. 1, Jan. 2022, Art. no. 1016. DOI: https://doi.org/10.1038/s41598-022-05005-4
D. G. Zisopol, I. Nae, A. I. Portoaca, and I. Ramadan, "A Theoretical and Experimental Research on the Influence of FDM Parameters on Tensile Strength and Hardness of Parts Made of Polylactic Acid," Engineering, Technology & Applied Science Research, vol. 11, no. 4, pp. 7458–7463, Aug. 2021. DOI: https://doi.org/10.48084/etasr.4311
D. G. Zisopol, I. Nae, A. I. Portoaca, and I. Ramadan, "A Statistical Approach of the Flexural Strength of PLA and ABS 3D Printed Parts," Engineering, Technology & Applied Science Research, vol. 12, no. 2, pp. 8248–8252, Apr. 2022. DOI: https://doi.org/10.48084/etasr.4739
A. Portoaca, I. Nae, D. G. Zisopol, and I. Ramadan, "Studies on the influence of FFF parameters on the tensile properties of samples made of ABS," IOP Conference Series: Materials Science and Engineering, vol. 1235, no. 1, Nov. 2022, Art. no. 012008. DOI: https://doi.org/10.1088/1757-899X/1235/1/012008
D. G. Zisopol, A. I. Portoaca, I. Nae, and I. Ramadan, "A Comparative Analysis of the Mechanical Properties of Annealed PLA," Engineering, Technology & Applied Science Research, vol. 12, no. 4, pp. 8978–8981, Aug. 2022. DOI: https://doi.org/10.48084/etasr.5123
J. M. Chacón, M. A. Caminero, E. García-Plaza, and P. J. Núñez, "Additive manufacturing of PLA structures using fused deposition modelling: Effect of process parameters on mechanical properties and their optimal selection," Materials & Design, vol. 124, pp. 143–157, Jun. 2017. DOI: https://doi.org/10.1016/j.matdes.2017.03.065
Z. Mehdiyev, C. Felhő, and K. P. Zoltán, "Investigation on 3D Printing Parameters of PLA Polymers for Gear Applications," in Vehicle and Automotive Engineering 4, 2023, pp. 654–664. DOI: https://doi.org/10.1007/978-3-031-15211-5_55
ISO 604:2002 - Plastics — Determination of compressive properties. ISO, 2002.
"3D CAD Design Software | SOLIDWORKS." https://www.solidworks.com/.
A. K. Sood, R. K. Ohdar, and S. S. Mahapatra, "Experimental investigation and empirical modelling of FDM process for compressive strength improvement," Journal of Advanced Research, vol. 3, no. 1, pp. 81–90, Jan. 2012. DOI: https://doi.org/10.1016/j.jare.2011.05.001
R. A. Cláudio, J. Dupont, R. Baptista, M. Leite, and L. Reis, "Behaviour evaluation of 3D printed polylactic acid under compression," Journal of Materials Research and Technology, vol. 21, pp. 4052–4066, Nov. 2022. DOI: https://doi.org/10.1016/j.jmrt.2022.10.042
D. G. Zisopol, D. V. Iacob, and A. I. Portoaca, "A Theoretical-Experimental Study of the Influence of FDM Parameters on PLA Spur Gear Stiffness," Engineering, Technology & Applied Science Research, vol. 12, no. 5, pp. 9329–9335, Oct. 2022. DOI: https://doi.org/10.48084/etasr.5183
Downloads
How to Cite
License
Copyright (c) 2022 DRAGOS GABRIEL ZISOPOL
This work is licensed under a Creative Commons Attribution 4.0 International License.
Authors who publish with this journal agree to the following terms:
- Authors retain the copyright and grant the journal the right of first publication with the work simultaneously licensed under a Creative Commons Attribution License that allows others to share the work with an acknowledgement of the work's authorship and initial publication in this journal.
- Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgement of its initial publication in this journal.
- Authors are permitted and encouraged to post their work online (e.g., in institutional repositories or on their website) after its publication in ETASR with an acknowledgement of its initial publication in this journal.