Enhancement of the Shear Capacity of RC Deep Beams with Ultra-High Performance Fiber-reinforced Concrete
Received: 1 December 2024 | Revised: 28 December 2024 | Accepted: 4 January 2025 | Online: 2 February 2025
Corresponding author: Mahmoud Elsayed
Abstract
This research investigates the shear behavior of Reinforced Concrete (RC) deep beams strengthened with Ultra-High-Performance Fiber-Reinforced Concrete (UHPFRC). For this purpose, eight RC deep beams were fabricated and tested for failure. One beam served as a control beam (un-strengthened), while the remaining seven deep beams were strengthened utilizing various strengthening schemes. This experimental study primarily focused on the thickness of the UHPFRC layer, Steel Fiber (SF) volume fraction, and strengthening schemes (jacketing, bilateral layers, and strips exclusively in the shear zone). The experimental findings demonstrated that UHPFRC significantly enhanced the shear capacity, toughness, and stiffness of the RC deep beams. The performance of the strengthened beams exhibited improvements in ultimate shear strength, stiffness, and toughness of about 43.6%, 102.2%, and 171.3%, respectively, higher than that of the un-strengthened deep beam. UHPFRC U-jacketing is a highly effective method for strengthening the RC deep beams. Incorporating SF into the UHPFRC mixture improved the shear properties of the strengthened specimens and delayed fracture propagation. Finally, the shear capacity of the strengthened specimens was compared to the values predicted by the analytical approaches presented in earlier research.
Keywords:
deep beams, shear behavior, strengthening, ultra-high-performance fiber reinforced concreteDownloads
References
E. G. Nawy, Reinforced Concrete: A Fundamental Approach. Prentice Hall, 2009.
A. C. I. Committee 318 and A. C. Institute, Building Code Requirements for Structural Concrete (ACI 318-08) and Commentary. American Concrete Institute, 2008.
A. Hussein, Z. M. R. A. Rasoul, and A. J. Alsaad, "Steel Fiber Addition in Eco-Friendly Zero-Cement Concrete: Proportions and Properties," Engineering, Technology & Applied Science Research, vol. 12, no. 5, pp. 9276–9281, Oct. 2022.
Standard practice for fabricating and testing Specimens of ultra-high performance concrete. ASTM International, 2024.
Test Method for Fluidity of Cement Mortar. China: GB National standard, 2005.
S. Astarlioglu and T. Krauthammer, "Response of normal-strength and ultra-high-performance fiber-reinforced concrete columns to idealized blast loads," Engineering Structures, vol. 61, pp. 1–12, Mar. 2014.
M. Amin, A. M. Zeyad, B. A. Tayeh, and I. Saad Agwa, "Effects of nano cotton stalk and palm leaf ashes on ultrahigh-performance concrete properties incorporating recycled concrete aggregates," Construction and Building Materials, vol. 302, Oct. 2021, Art. no. 124196.
A. S. Faried, S. A. Mostafa, B. A. Tayeh, and T. A. Tawfik, "The effect of using nano rice husk ash of different burning degrees on ultra-high-performance concrete properties," Construction and Building Materials, vol. 290, Jul. 2021, Art. no. 123279.
B. A. Tayeh, A. S. Aadi, N. N. Hilal, B. H. A. Bakar, M. M. Al-Tayeb, and W. N. Mansour, "Properties of ultra-high-performance fiber-reinforced concrete (UHPFRC)—a review paper," AIP Conference Proceedings, vol. 2157, no. 1, Sep. 2019, Art. no. 020040.
R. K. Biswas et al., "Effects of Steel Fiber Percentage and Aspect Ratios on Fresh and Harden Properties of Ultra-High Performance Fiber Reinforced Concrete," Applied Mechanics, vol. 2, no. 3, pp. 501–515, Sep. 2021.
M. A. Al-Osta, M. N. Isa, M. H. Baluch, and M. K. Rahman, "Flexural behavior of reinforced concrete beams strengthened with ultra-high performance fiber reinforced concrete," Construction and Building Materials, vol. 134, pp. 279–296, Mar. 2017.
A. P. Lampropoulos, S. A. Paschalis, O. T. Tsioulou, and S. E. Dritsos, "Strengthening of reinforced concrete beams using ultra high performance fibre reinforced concrete (UHPFRC)," Engineering Structures, vol. 106, pp. 370–384, Jan. 2016.
M. Safdar, T. Matsumoto, and K. Kakuma, "Flexural behavior of reinforced concrete beams repaired with ultra-high performance fiber reinforced concrete (UHPFRC)," Composite Structures, vol. 157, pp. 448–460, Dec. 2016.
Y. Zhang, X. Li, Y. Zhu, and X. Shao, "Experimental study on flexural behavior of damaged reinforced concrete (RC) beam strengthened by toughness-improved ultra-high performance concrete (UHPC) layer," Composites Part B: Engineering, vol. 186, Apr. 2020, Art. no. 107834.
H. A. Alasmari, "The Influence of UHPFRC Jacket Steel Fiber Content on Strengthening Damaged Columns," Engineering, Technology & Applied Science Research, vol. 13, no. 5, pp. 11965–11972, Oct. 2023.
Standard Practice for Selecting Proportions for Normal, Heavyweight, and Mass Concrete (ACI 211.1-91). ACI, 1991.
Standard Test Method for Relative Density (Specific Gravity) and Absorption of Coarse Aggregate. ASTM International, 2024.
Standard Test Method for Relative Density (Specific Gravity) and Absorption of Fine Aggregate. ASTM International, 2023.
Standard Test Method for Compressive Strength of Cylindrical Concrete Specimens. ASTM International, 2001.
Standard Test Methods and Definitions for Mechanical Testing of Steel Products. ASTM International, 2003.
I. L. Howard, B. Hansen, T. Wilson, and V. T. Cost, "Portland-Limestone Cement’s Implementation into Mississippi’s Concrete Market," Journal of Testing and Evaluation, vol. 50, no. 2, pp. 1182–1198, Mar. 2022.
Standard Specification for Chemical Admixtures for Concrete. USA: ASTM International, 2017.
"Kemapoxy 165 – CMB." https://www.cmbegypt.com/cmb/en/product/kemapoxy-165/.
"Kemapoxy 104 – CMB." https://www.cmbegypt.com/cmb/en/product/kemapoxy-104/.
A. Yavaş, T. Birol, K. Türker, U. Hasgül, and H. Yazıcı, "Improvement on Flexural Performance of UHPFRC with Hybrid Steel Fiber," Teknik Dergi, vol. 31, no. 6, pp. 10379–10397, Nov. 2020.
A. Beglarigale, Ç. Yalçınkaya, and H. Yazıcı, "Autoclaved reactive powder concrete: the effects of steel micro-fibers and silica fume dosage on the mechanical properties," Usak University Journal of Material Sciences, vol. 3, no. 1, pp. 7–14, Jul. 2014.
A. Said, M. Elsayed, A. A. El-Azim, F. Althoey, and B. A. Tayeh, "Using ultra-high performance fiber reinforced concrete in improvement shear strength of reinforced concrete beams," Case Studies in Construction Materials, vol. 16, Jun. 2022, Art. no. e01009.
L. Hussein and L. Amleh, "Structural behavior of ultra-high performance fiber reinforced concrete-normal strength concrete or high strength concrete composite members," Construction and Building Materials, vol. 93, pp. 1105–1116, Sep. 2015.
Building Code Requirements for Structural Concrete (ACI 318-19) and Commentary. ACI, 2020.
H. Yokota, K. Rokugo, and N. Sakata, "JSCE Recommendations for Design and Construction of High Performance Fiber Reinforced Cement Composite with Multiple Fine Cracks," Japan Society of Civil Engineers, Mar. 2007.
B. A. Graybeal and United States. Federal Highway Administration. Office of Infrastructure Research and Development, "Structural Behavior of Ultra-High Performance Concrete Prestressed I-Girders," FHWA-HRT-06-115, Jan. 2006. [Online]. Available: https://rosap.ntl.bts.gov/view/dot/41899.
Y. M. Abbas, "Shear behavior of ultra-high-performance reinforced concrete beams – Finite element and uncertainty quantification study," Structures, vol. 47, pp. 2365–2380, Jan. 2023.
Downloads
How to Cite
License
Copyright (c) 2025 Ahmed Abd Elghany, Mahmoud Elsayed, Alaa Elsayed, Ayman Shaheen
This work is licensed under a Creative Commons Attribution 4.0 International License.
Authors who publish with this journal agree to the following terms:
- Authors retain the copyright and grant the journal the right of first publication with the work simultaneously licensed under a Creative Commons Attribution License that allows others to share the work with an acknowledgement of the work's authorship and initial publication in this journal.
- Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgement of its initial publication in this journal.
- Authors are permitted and encouraged to post their work online (e.g., in institutional repositories or on their website) after its publication in ETASR with an acknowledgement of its initial publication in this journal.
