Integration of Scanning Technology for Tool Wear Analysis in the Electrical Discharge Machining Process

Authors

  • Osama Sameer Sabbar Department of Production Engineering and Metallurgy, University of Technology, Iraq
  • Ali Abbar Khleif Department of Production Engineering and Metallurgy, University of Technology, Iraq
  • Baraa M. H. Albaghdadi Department of Production Engineering and Metallurgy, University of Technology, Iraq
  • Nader Abdulhameed Division of Prosthodontics, Restorative Dental Sciences, University of Florida, USA
Volume: 14 | Issue: 5 | Pages: 17035-17040 | October 2024 | https://doi.org/10.48084/etasr.7989

Abstract

There is a direct correlation between surface roughness and electrode tool status in the Electrical Discharge Machining (EDM) process. The quality of the machined surface of workpieces is becoming even more critical in recent industries. In general, electrode wear evaluation plays a vital role in the EDM process, affecting the operation cost and the accuracy of the required dimensions and geometric shape. This study presents a new method to evaluate the copper electrode wear during machining AISI 1005 carbon steel in the EDM process using a 3D laser scanner that measures the lost volume of the electrode. The results of the proposed method were compared with those of the conventional method. Laser technology was used to accurately measure the dimensions and surface characteristics of the electrode by scanning the electrode surface and the electrode view topology before and after the machining process. The processed data was saved on a computer connected to the laser scan device, converted to STL files, and sent to a 3D system (Geomagic Control X software). This software utilizes accurate mathematical algorithms to determine the available volumetric differences in the electrode. The experiments used Design-Expert 13 software, selecting three machining parameters: Current (Ip), pulse on time (Ton), and pulse off time (Toff). The results showed that the Tool Wear Rate (TWR) obtained by the two methods showed a mean absolute deviation of 3.6%, with an insignificant error on the effect of the machining parameters on TWR (1.01% for Ip, 1.92% for Ton, and 2.29% for Toff).

Keywords:

EDM, laser scan technique, electrode wear, Geomagic Control X, TWR measurement

Downloads

Download data is not yet available.

References

S. Anjum, M. Shah, N. A. Anjum, S. Mehmood, and W. Anwar, "Machining and Surface Characteristics of AISI 304L After Electric Discharge Machining for Copper and Graphite Electrodes in Different Dielectric Liquids," Engineering, Technology & Applied Science Research, vol. 7, no. 4, pp. 1765–1770, Aug. 2017.

N. V. Cuong and N. L. Khanh, "Parameter Selection to Ensure Multi-Criteria Optimization of the Taguchi Method Combined with the Data Envelopment Analysis-based Ranking Method when Milling SCM440 Steel," Engineering, Technology & Applied Science Research, vol. 11, no. 5, pp. 7551–7557, Oct. 2021.

V. C. Nguyen, T. D. Nguyen, and D. H. Tien, "Cutting Parameter Optimization in Finishing Milling of Ti-6Al-4V Titanium Alloy under MQL Condition using TOPSIS and ANOVA Analysis," Engineering, Technology & Applied Science Research, vol. 11, no. 1, pp. 6775–6780, Feb. 2021.

N. Mohri and T. Tani, "Recent evolution of electrical discharge machining," in 4M 2006 - Second International Conference on Multi-Material Micro Manufacture, Oxford, UK, Jan. 2006, pp. 23–26.

Y. Laibi and S. Shather, "Effect of SiC-Cu Electrode on Material Removal Rate, Tool Wear and Surface Roughness in EDM Process," Engineering and Technology Journal, vol. 38, no. 9, pp. 1406–1413, Sep. 2020.

J. E. A. Qudeiri, A. Zaiout, A.-H. I. Mourad, M. H. Abidi, and A. Elkaseer, "Principles and Characteristics of Different EDM Processes in Machining Tool and Die Steels," Applied Sciences, vol. 10, no. 6, Jan. 2020, Art. no. 2082.

A. R. Hayyawi, H. Al-Ethari, and A. H. Haleem, "Optimization of the PM-EDM Process Parameters for Ti-35Nb-7Zr-5Ta Bio Alloy," Engineering, Technology & Applied Science Research, vol. 14, no. 3, pp. 13982–13989, Jun. 2024.

J. E. Abu Qudeiri, A. Saleh, A. Ziout, A.-H. I. Mourad, M. H. Abidi, and A. Elkaseer, "Advanced Electric Discharge Machining of Stainless Steels: Assessment of the State of the Art, Gaps and Future Prospect," Materials, vol. 12, no. 6, 2019.

M. Bellotti, M. Wu, J. Qian, and D. Reynaerts, "Tool Wear and Material Removal Predictions in Micro-EDM Drilling: Advantages of Data-Driven Approaches," Applied Sciences, vol. 10, no. 18, Jan. 2020, Art. no. 6357.

G. Malayath, S. Katta, A. M. Sidpara, and S. Deb, "Length-wise tool wear compensation for micro electric discharge drilling of blind holes," Measurement, vol. 134, pp. 888–896, Feb. 2019.

A. A. Khleif, "Computer Vision Aided Electrode Wear Estimation in Electrical Discharge Machining Process," Journal of Engineering Science and Technology Review, vol. 17, no. 1, pp. 197–206, 2022.

H. R. Gurupavan, H. V. Ravindra, T. M. Devegowda, and R. Addamani, "Machine Vision System for Correlating Wire Electrode Status and Machined Surface in WEDM of AlSi3N4 MMC’S," IOP Conference Series: Materials Science and Engineering, vol. 376, no. 1, Mar. 2018, Art. no. 012120.

Z. Hamedon, I. Razemi, A. R. Abdul Manaf, and N. M. Yahya, "Innovative Method of Measuring Electrode Wear During EDM Drilling Process Using Vision System," in Intelligent Manufacturing & Mechatronics, Pekan, Malaysia, 2018, pp. 53–63.

A. A. Khleifa and O. S. Sabbar, "Electrode Wear Evaluation in E.D.M Process," Engineering and Technology Journal, vol. 37, no. 2C, pp. 252–257, May 2019.

S. M. Hsu, F. Ren, N. Abdulhameed, M. Kim, D. Neal, and J. Esquivel-Upshaw, "Comprehensive analysis of laserscanner validity used for measurement of wear," Journal of Oral Rehabilitation, vol. 46, no. 6, pp. 503–510, 2019.

A. A. Khleif, "Experimental investigation of electrode wear assessment in the EDM process using image processing technique," Open Engineering, vol. 13, no. 1, Jan. 2023.

A. A. Khan, "Electrode wear and material removal rate during EDM of aluminum and mild steel using copper and brass electrodes," The International Journal of Advanced Manufacturing Technology, vol. 39, no. 5, pp. 482–487, Nov. 2008.

C. Kühne, U. Lohbauer, S. Raith, and S. Reich, "Measurement of Tooth Wear by Means of Digital Impressions: An In-Vitro Evaluation of Three Intraoral Scanning Systems," Applied Sciences, vol. 11, no. 11, Jan. 2021, Art. no. 5161.

A. M. Abbas and A. A. Khleif, "EDM Electrode Design and Analysis to Enhance Process Performance," Tikrit Journal of Engineering Sciences, vol. 30, no. 4, pp. 145–152, Dec. 2023.

D. T. Pham, A. Ivanov, S. Bigot, K. Popov, and S. Dimov, "A study of micro-electro discharge machining electrode wear," Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science, vol. 221, no. 5, pp. 605–612, May 2007.

J. P. Santos, J. Macedo, H. Ávila, G. Lima, E. Arruda, and A. Lazaroni, "Innovative Refractory Wear Measurement Method for Steel Ladles Using 3D Laser Scanning," RHI Magnesita Bulletin, pp. 57–60, 2023.

Ľ. Straka and P. Kuchta, "Dynamic control of discharge energy during wedm for the purpose of eliminating vibrations of the wire tool electrode," Management Systems in Production Engineering, vol. 29, no. 4, pp. 260–265, 2021.

Z. Chaowen, J. Jing, and C. Chi, "Research On Tool Wear Monitoring Based On GRU-CNN," in 2021 6th International Conference on Intelligent Computing and Signal Processing (ICSP), Xi’an, China, Apr. 2021, pp. 729–733.

D. Ninevski, Y. Yifrach, and P. O’Leary, "Instrumented Milling Process and Analysis for Tool Wear Measurement," in 2023 IEEE International Instrumentation and Measurement Technology Conference (I2MTC), Kuala Lumpur, Malaysia, May 2023, pp. 1–6.

W. K. Jang, D. W. Kim, Y. H. Seo, and B. H. Kim, "Tool-Wear-Estimation System in Milling Using Multi-View CNN Based on Reflected Infrared Images," Sensors, vol. 23, no. 3, Jan. 2023, Art. no. 1208.

R. G. Lins, B. Guerreiro, P. R. Marques de Araujo, and R. Schmitt, "In-Process Tool Wear Measurement System Based on Image Analysis for CNC Drilling Machines," IEEE Transactions on Instrumentation and Measurement, vol. 69, no. 8, pp. 5579–5588, Dec. 2020.

D. C. Viegas et al., "Evaluation of the influence of the impression technique, scanning direction and type of scanner on the accuracy of the final model," Brazilian Dental Science, vol. 24, no. 1, 2021.

Downloads

How to Cite

[1]
Sabbar, O.S., Khleif, A.A., Albaghdadi, B.M.H. and Abdulhameed, N. 2024. Integration of Scanning Technology for Tool Wear Analysis in the Electrical Discharge Machining Process. Engineering, Technology & Applied Science Research. 14, 5 (Oct. 2024), 17035–17040. DOI:https://doi.org/10.48084/etasr.7989.

Metrics

Abstract Views: 39
PDF Downloads: 76

Metrics Information