Design and Failure Analysis of a Vacuum Pressure Vessel for Aerospace Applications using Finite Element Analysis (FEA)

Authors

  • Eiman Solangi Department of Mechanical Engineering, University Technology Petronas, Seri Iskandar, Malaysia
  • Thar Muhammad Badri Albarody Department of Mechanical Engineering, University Technology Petronas, Seri Iskandar, Malaysia
  • Sarah Al-Challabi Department of Mechanical Engineering, University Technology Petronas, Seri Iskandar, Malaysia
  • Javed Akbar Khan Department of Electrical and Mechanical Engineering, China University of Petroleum, Qingdao, China
  • Sajjad Ali Department of Mechanical Engineering, University Technology Petronas, Seri Iskandar, Malaysia
Volume: 14 | Issue: 6 | Pages: 17888-17893 | December 2024 | https://doi.org/10.48084/etasr.7673

Abstract

This paper provides detailed insights into the external pressure vessels. External pressure vessels are designed to perform under extreme operating conditions, so the selection of material and geometry along with stress analysis are fundamental for their optimal efficiency. The objective of this research is to provide a case study of the material, design, and stress generated in the pressure vessel to make it suitable for thermal and load-bearing applications in the aerospace industry. An aluminum alloy was chosen as the design material due to its low density and high strength. The modeling geometry of the alloy was constructed using the ASME section-VIII division-I div code. After the performed Finite Element Analysis (FEA), modeling was carried out deploying the ANSYS design modeler to obtain the stress concentration and failure mode of the model. The present study demonstrates the behavior of a structure under applied load and identifies the weak areas of its geometry. Based on the external stress at the center of the structure, the maximum and minimum stresses computed are 0.763 MPa and 0.00803 MPa, respectively. It was also found that the maximum strain is generated at the center of the structure and is equal to 1.0834e-6 mm/mm, the maximum deformation is equal to 0.00109 mm and also occurred at the center, while the shells of the model are unable to undergo any deformation. FEA results agree with the analytical results, as the errors for hoop stress and equivalent strain are 4.8% and 1.8%, respectively. Thus, the proposed method can be applied to predict the equivalent stress, equivalent strain, total deformation, and stress intensity, which are required for the structural integrity analysis of pressure vessels.

Keywords:

finite element analysis, pressure vessel, ASME code compliance, stress concentration

Downloads

Download data is not yet available.

References

K. Khadke and Dr. D. Chawde, "Design & Finite Element Analysis of Pressure Vessel," International Journal for Research in Applied Science & Engineering Technology (IJRASET), vol. 10, no. 7, pp. 4741–4748, Jul. 2022.

D. Koulocheris and C. Vossou, "Exploration of Equivalent Design Approaches for Tanks Transporting Flammable Liquids," Computation, vol. 8, no. 2, Jun. 2020, Art. no. 33.

S. Moyya, P. Thejasree, B. Cherian Abraham, and G. S. Mangalathu, "Design and analysis of single and multi-layer pressure vessel," Materials Today: Proceedings, Jul. 2023.

V. Chowdary, "Design and Static Analysis of Different Pressure Vessels and Materials Using FEM Method," International Journal of Advance Scientific Researchand Engineering Trends, vol. 5, no. 7, pp. 93–99, Jul. 2020.

I. Gophane, N. Dharashivkar, P. Mulik, and P. Patil, "Theoretical and Finite Element Analysis of Pressure Vessel," Indian Journal of Science and Technology, vol. 17, no. 12, pp. 1148–1158, Mar. 2024.

I. Ramos, Y. Ho Park, and J. Ulibarri-Sanchez, "Analytical and Numerical Studies of a Thick Anisotropic Multilayered Fiber-Reinforced Composite Pressure Vessel," Journal of Pressure Vessel Technology, vol. 141, Dec. 2018, , Art. no. 011203.

J. Pratama, D. F. Fitriyana, Rusiyanto, J. P. Siregar, and W. Caesarendra, "A low cost validation method of finite element analysis on a thin walled vertical pressure vessels," Journal of Physics: Conference Series, vol. 1444, no. 1, Jan. 2020, Art. no. 012042.

G. Terán, S. Capula-Colindres, J. C. Velázquez, D. Angeles-Herrera, and E. Torres-Santillán, "On the Influence of the Corrosion Defect Size in the Welding Bead, Heat-Affected Zone, and Base Metal in Pipeline Failure Pressure Estimation: A Finite Element Analysis Study," Journal of Pressure Vessel Technology, vol. 141, Apr. 2019, Art. no. 031001.

B. Siva kumar, P. Prasanna, J. Sushma, and K. P. Srikanth, "Stress Analysis And Design Optimization Of A Pressure Vessel Using Ansys Package," Materials Today: Proceedings, vol. 5, no. 2, Part 1, pp. 4551–4562, Jan. 2018.

S. J. Niranjana, S. V. Patel, and A. K. Dubey, "Design and Analysis of Vertical Pressure Vessel using ASME Code and FEA Technique," IOP Conference Series: Materials Science and Engineering, vol. 376, no. 1, Mar. 2018, Art. no. 012135.

M. M. Islam, M. F. Hossain, M. S. Rana, and M. S. Ferdous, "Burst pressure prediction of carbon/natural fiber and hybrid composite pressure vessels by theoretical and numerical analysis," Hybrid Advances, vol. 5, Apr. 2024, Art. no. 100172.

A. Kothali, U. Bhapkar, and J. Bhat, "Finite element analysis of bursting pressure in FRP pressure vessel," Materials Today: Proceedings, vol. 56, pp. 2932–2937, Jan. 2022.

J. Sun, J. Xin, and Y. Wang, "Stress Analysis of Pressure Vessels Based on ANSYS," International Journal of Trend in Research and Development, vol. 5, no. 4, pp. 298–301, Aug. 2018.

S. R. Gupta and C. P. Vora, "A Review Paper on Pressure Vessel Design and Analysis," International Journal of Engineering Research, vol. 3, no. 3, pp. 295–300, Mar. 2014.

A. Akhmeteli and A. V. Gavrilin, "Vacuum Balloon–A 350-Year-Old Dream," Eng, vol. 2, no. 4, pp. 480–491, Dec. 2021.

D. Glasberg, S. Stratila, and I. Malael, "A Numerical Analysis on the Performance and Optimization of the Savonius Wind Turbine for Agricultural Use," Engineering, Technology & Applied Science Research, vol. 14, no. 1, pp. 12621–12627, Feb. 2024.

S. Salins, M. Mohan, and C. Stephen, "Finite Element Investigation on the Performance of Pressure Vessel Subjected to Structural Load," Annales de Chimie - Science des Matériaux, vol. 45, pp. 201–205, Jun. 2021.

S. Parkhe and K. Annamalai, "Design and Analysis of Pressure Vessel Subjected to Pressure-temperature Variation," International Journal of Engineering, vol. 31, no. 1, pp. 58–64, Jan. 2018.

K. Kazeem, A. F. Abdulfatai, and E. A. Edith, "Design and Analysis of a Vertical Pressure Vessel with Effect of Rotational Velocity on the Stresses and Deformation by using ANSYS," International Journal of Analytical, Experimental and Finite Element Analysis, pp. 110–120, Oct. 2019.

N. Pervan, M. Trobradovic, A. J. Muminovic, H. Lulic, S. Metovic, and V. Hadziabdic, "Effects of Geometry Design Parameters on the Fatigue Failure of a Drive Axle Housing using Finite Element Analysis," Engineering, Technology & Applied Science Research, vol. 14, no. 1, pp. 12567–12573, Feb. 2024.

V. V. Wadkar, S. S. Malgave, D. D. Patil, H. S. Bhore, and P. P. Gavade, "Design and Analysis of Pressure Vessel Using ANSYS," Journal of Mechanical Engineering and Technology (JMET), vol. 3, no. 2, pp. 01–13, Oct. 2015.

Y.-J. Lu and C.-H. Wang, "A finite element-based analysis approach for computing the remaining strength of the pressure equipment with a local thin area defect," Engineering Failure Analysis, vol. 131, Jan. 2022, Art. no. 105883.

E. Solangi, I. Memon, M. Memon, M. Raees, and M. Khan, "Failure Analysis of a Diesel Engine Crankshaft based on Finite Element Modeling," Journal of Applied Engineering & Technology (JAET), vol. 7, pp. 1–9, Jun. 2023.

Downloads

How to Cite

[1]
Solangi, E., Albarody, T.M.B., Al-Challabi, S., Khan, J.A. and Ali, S. 2024. Design and Failure Analysis of a Vacuum Pressure Vessel for Aerospace Applications using Finite Element Analysis (FEA). Engineering, Technology & Applied Science Research. 14, 6 (Dec. 2024), 17888–17893. DOI:https://doi.org/10.48084/etasr.7673.

Metrics

Abstract Views: 155
PDF Downloads: 218

Metrics Information

Most read articles by the same author(s)