A Surface Roughness Analysis of 3D Printed Mold Inserts Using ABS-Like and TR300 Resins: An Evaluation of Printing Angles and Material Performance for Injection Molding Applications
Received: 03 April 2025 | Revised: 28 May 2025 | Accepted: 7 June 2025 | Online: 2 August 2025
Corresponding author: Jak Chuanasa
Abstract
This research focuses on a comparative study of the surface roughness of parts fabricated using Stereolithography (SLA) 3D printing technology. The objective is to compare the surface roughness of printed parts at various build angles, ranging from 0° to 90°, using two types of resins: Acrylonitrile Butadiene Styrene (ABS)-like resin and TR300 resin. The study aims to determine whether the surface roughness trends are consistent between the two materials and to analyze the effect of printing angle on surface quality. This analysis will identify the optimal printing conditions for producing high-quality insert mold cavities used in plastic injection molding. The experimental results reveal that TR300 resin consistently provides a smoother surface finish than ABS-like resin across all printing angles. The lowest surface roughness was observed at a 0° printing angle with TR300 resin, showing values of Ra = 0.175 µm, Rz = 1.123 µm, and Rt = 1.136 µm. In comparison, the lowest surface roughness for ABS-like resin at the same angle was Ra = 0.256 µm, Rz = 1.690 µm, and Rt = 2.170 µm. These findings indicate that the most suitable condition for producing insert mold cavities for high-quality plastic injection molds is using TR300 resin printed at a 0° angle. This is due to the fact that the resulting surface roughness falls within the recommended range for mold cavities (Ra = 0.2–1.6 µm), making it ideal for precision applications in injection molding.
Keywords:
3D printing, surface roughness, ABS-like resin, TR300 resin, injection molding, printing angle, surface finishDownloads
References
A. Alghamdi, "LoRe-GRNN: A Hybrid Deep Learning Framework for Real-Time Anomaly Detection and Stress Distribution Prediction in 3D Printing Processes," Engineering, Technology & Applied Science Research, vol. 15, no. 2, pp. 21671–21677, Apr. 2025. DOI: https://doi.org/10.48084/etasr.10102
A. Komjaty, E. S. Wisznovszky (Muncut), and L. I. Culda, "Study on the influence of technological parameters on 3D printing with sla technology," MATEC Web of Conferences, vol. 343, 2021, Art. no. 01003. DOI: https://doi.org/10.1051/matecconf/202134301003
T. R. Mhmood and N. K. Al-Karkhi, "A Review of the Stereo lithography 3D Printing Process and the Effect of Parameters on Quality," Al-Khwarizmi Engineering Journal, vol. 19, no. 2, pp. 82–94, Jun. 2023. DOI: https://doi.org/10.22153/kej.2023.04.003
S. S.-N. Lu, "Improving surface quality of SLA 3D printed parts via controlled dip-coating," B.S. thesis, Department of Mechanical Engineering, Massachusetts Institute of Technology, Cambridge, MA, USA, 2018.
M. Mischkot, G. Tosello, D. K. Y. Nielsen, and D. B. Pedersen, "Injection Moulding Pilot Production: Performance Assessment of Tooling Process Chains Based on Tool Inserts Made from Brass and A 3d Printed Photopolymer," in Annual Technical Conference (ANTEC 2017) of the Society of Plastic Engineers, Anaheim, CA, USA, 2017, pp. 1898–1902.
A. Katheng, W. Prawatvatchara, W. Tonprasong, S. Namano, and P. Kongkon, "Effect of Postrinsing Times and Methods on Surface Roughness, Hardness, and Polymerization of 3D-Printed Photopolymer Resin," European Journal of Dentistry, vol. 19, no. 1, pp. 154–164, May 2024. DOI: https://doi.org/10.1055/s-0044-1786866
User_Manual_Sonic_Mega_8K_S_manual_EN_v1.1.0. Accessed: Jun. 12, 2025. [Online]. Available: https://cdn.shopify.com/s/files/1/0436/6965/1618/files/User_Manual_Sonic_Mega_8K_S_manual_EN_v1.1.0.pdf?v=1734338092.
User_Guide_Tough_ABS_Like_EN. Accessed: Jun. 12, 2025. [Online]. Available: https://cdn.shopify.com/s/files/1/0436/6965/1618/files/User_Guide_Tough_ABS_Like_EN.pdf?v=1742872340.
User_Guide_TR300_Gray_EN_V4. Accessed: Jun. 12, 2025. [Online]. Available: https://cdn.shopify.com/s/files/1/0436/6965/1618/files/User_Guide_TR300_Gray_EN_V4.pdf?v=1727079346.
S. Koffaree, "Roughness testing." IKKI Group. https://ikki-group.com/roughness-testing/.
"Engineering drawing 03." Nexpert. https://www.nextpert.co.th/information/eng-dwg/eng-dwg-03.
Jon, "The Ultimate Guide to Surface Finish Standards: Symbols, Charts, Techniques, & Applications." Jiga. https://jiga.io/articles/surface-finish/.
S. Elder, "The Basics of Surface Finish." GD&T Basics. https://www.gdandtbasics.com/basics-of-surface-finish/.
M. R. Mahadeshwara, "Stylus profilometer - About Tribology." Tribonet. https://www.tribonet.org/wiki/stylus-profilometera-stylus-profilometer-is-a-contact-based-profilometer-that-brings-its-stylus-tip-into-direct-contact-with-the-measuring-surface-and-traces-the-desired-path-to-determine-the-topograp/.
"Introduction to Surface Roughness Measurement." Sernia. https://sernia.ru/upload/pdf_files/Introduction%20to%20surface%20roughness%20measurement.pdf.
Jenoptik, "Precise roughness measurement: Surface texture parameters in practice." Tecotecshop. https://cdn.tecotecshop.com/Repository/Jenoptik/W800/roughness-leaflet-en.pdf.
"Precise roughness measurement: Surface texture parameters in practice-poster." Jenoptik. https://www.jenoptik.com/-/media/hommel-etamic-documents/metrology/neu/parameters/roughness-measurement-poster-en.pdf.
H. P. Varade, "Surface Roughness Metrology." Indus University Course Content. https://coursecontent.indusuni.ac.in/wp-content/uploads/sites/8/2021/10/BAS_Surface-roughness-2.pdf.
Downloads
How to Cite
License
Copyright (c) 2025 Soontorn Weeradeachlikul, Jak Chuanasa
This work is licensed under a Creative Commons Attribution 4.0 International License.
Authors who publish with this journal agree to the following terms:
- Authors retain the copyright and grant the journal the right of first publication with the work simultaneously licensed under a Creative Commons Attribution License that allows others to share the work with an acknowledgement of the work's authorship and initial publication in this journal.
- Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgement of its initial publication in this journal.
- Authors are permitted and encouraged to post their work online (e.g., in institutional repositories or on their website) after its publication in ETASR with an acknowledgement of its initial publication in this journal.
